Do you have questions? Our community may have already answered them!
Connect with others in our support forum.
Kinco RP20 digital expansion with 8 or 16 I/Os for AK8x0M PLC and RP20 bus coupler
- 8 or 16 channels per module
- Transistor PNP or relay
- Transistor switches below 50 µs
- Short-circuit & overcurrent proof
- 12 mm wide (relay 24 mm)
€56.81*
In stock
Lieferzeit: 3 bis 5 TageCustomers also bought
Customers also viewed
Running out of inputs or outputs on your controller, with hardly any space left in the cabinet? The digital RP20 modules provide 8 or 16 channels on a width of 12 mm (relay module 24 mm), as transistor or relay versions. They plug directly onto the Kinco AK840M or onto an RP20 bus coupler; inputs and transistor outputs switch in less than 50 µs.
🏭 Typical Applications
Reading sensors and push buttons: Limit switches, proximity switches and operator controls on 16 inputs, PNP or NPN.
Driving valves and contactors: Solenoid valves, indicator lamps and auxiliary contactors via 24 V DC transistor outputs.
Potential-free contacts: With the relay module you switch 250 V AC or 30 V DC, e.g. for third-party controls or signalling devices.
Decentralised I/O stations: Together with the EtherCAT or CANopen coupler as remote I/O right at the machine.
🧩 Variants
RP20-1600DT: 16 digital inputs 24 V DC, PNP and NPN, adjustable filter time.
RP20-0016DTP: 16 transistor outputs 24 V DC, PNP.
RP20-0808DTP: 8 digital inputs PNP and 8 transistor outputs PNP, 24 V DC.
RP20-0008DR: 8 relay outputs, normally open, potential-free, 250 V AC / 30 V DC, 2 A per channel, 8 A per module.
🖥️ Key Technical Specs
Inputs: 24 V DC, approx. 3.5 mA per channel, input impedance 6.8 kΩ; signal 0 up to 5 V, signal 1 from 15 V.
Transistor outputs: 24 V DC (20.4 – 28.8 V DC), leakage current max. 10 µA, up to 100 Hz with resistive load.
Relay outputs: up to 20 switching cycles per minute, mechanical life 20 million, electrical 100,000 cycles; separate 24 V supply (approx. 60 mA).
Switching time: turn-on and turn-off delay below 50 µs for inputs and transistor outputs, below 15 ms for the relay module.
Isolation and protection: galvanically isolated; outputs with short-circuit and overcurrent protection.
Indication: green LED per channel, LEDs PR and ERR for status and errors.
🔗 Compatibility
The modules plug directly onto the side of the Kinco AK840M or onto an RP20 bus coupler: RP20C-ECT for EtherCAT, RP20C-CAN for CANopen. Up to 16 modules per station, configured in CODESYS (IEC 61131-3).
Analogue: RP20 analogue modules: current and voltage signals.
Temperature: RP20 temperature modules: resistance thermometers and thermocouples.
⚠️ Good to Know
Plan the bus current: Each module draws 135 mA from the internal K-BUS. An RP20 bus coupler supplies 2.0 A (1.6 A at 55 °C), the AK8X0 1.5 A. If the total is not sufficient, add an RP20-PW power supply module to the station.
No hot swap: Only plug in or remove modules with the power switched off.
🏷️ Manufacturer and Standards
Kinco Automation develops PLCs, HMIs and drive technology. The RP20 modules are CE certified according to EN IEC 61000-6-2:2019 and EN IEC 61000-6-4:2019, EMC immunity according to IEC 61131-2, zone B. Operation −20 °C to +55 °C, storage −40 °C to +70 °C, 10 to 95 % relative humidity non-condensing, IP20.
🔧 Mounting and Scope of Delivery
Mounting: 35 mm DIN rail; the modules snap onto their neighbour sideways via upper and lower guides.
Dimensions: 12 × 100 × 80 mm (W × H × D), approx. 70 g; RP20-0008DR: 24 × 100 × 80 mm, approx. 120 g, passive cooling.
Scope of delivery: one module of the selected variant.
Technical Specifications
Login