You need a controller for a machine with a manageable number of signals and want to expand later without replacing the PLC? The Kinco K606-24 comes with 14 digital inputs, 10 outputs, Ethernet and two galvanically isolated RS-485 ports, and grows with your system via one BD slot and up to 14 expansion modules. 🏭 Typical applications Conveying and packaging: belts, diverters and feeders. The high-speed counters read encoders up to 200 kHz directly on the device. Positioning with stepper or servo drives: the transistor variants output pulse and direction on four channels, three of them up to 200 kHz. Pumps, fans and frequency inverters: control drives and meters directly via Modbus RTU on RS-485. Connection to HMI and control system: Modbus TCP via Ethernet, for example to a Kinco HMI or a higher-level SCADA. ⚙️ Four variants K606-24DT: 24 V DC supply, 10 PNP transistor outputs K606-24AT: 100 – 240 V AC supply, 10 PNP transistor outputs K606-24DR: 24 V DC supply, 10 relay outputs K606-24AR: 100 – 240 V AC supply, 10 relay outputs 💡 The relay variants have no pulse outputs. For positioning tasks, choose DT or AT. ⚡ Inputs and outputs 14 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Relay outputs: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels, electrical life 100 000 operations at rated load. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs (transistor variants only): 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. Positioning instructions and a follow function are included in KincoBuilder. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion One BD slot takes an expansion board directly on the CPU: KB6-CAN (CANopen master), KB6-2COM (RS-232 + RS-485), KB6-4DI or KB6-4DO. On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K606-24 is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 128 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

Your system has more sensors and actuators than a compact PLC with 24 channels can handle? The Kinco K608-40 comes with 24 digital inputs and 16 outputs, plus two BD slots for CAN, additional interfaces or I/O. Many machines manage without a single expansion module. 🏭 Typical applications Multi-station machines: assembly, test and packaging lines with many limit switches, light barriers and valves. Drives via CANopen: with the KB6-CAN board you control up to 64 CANopen nodes, or Kinco servo and stepper drives via the Kinco motion protocol. Positioning: the transistor variants output pulse and direction on four channels, three of them up to 200 kHz. Building services: pumps, ventilation and inverters via Modbus RTU, visualisation via Modbus TCP. ⚙️ Four variants K608-40DT: 24 V DC supply, 16 PNP transistor outputs K608-40AT: 100 – 240 V AC supply, 16 PNP transistor outputs K608-40DR: 24 V DC supply, 16 relay outputs K608-40AR: 100 – 240 V AC supply, 16 relay outputs 💡 The relay variants have no pulse outputs. For positioning tasks, choose DT or AT. ⚡ Inputs and outputs 24 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Relay outputs: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels, electrical life 100 000 operations at rated load. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs (transistor variants only): 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. Positioning instructions and a follow function are included in KincoBuilder. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion Two BD slots take expansion boards directly on the CPU. BD0 accepts communication and I/O boards (KB6-CAN, KB6-2COM, KB6-4DI, KB6-4DO), BD1 accepts I/O boards only (KB6-4DI, KB6-4DO). On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K608-40 is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 186 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

Your machine needs to measure pressures, temperatures or levels and drive an inverter via an analog signal, not just switch? The Kinco K606EA-30DT already has 4 analog inputs and 2 analog outputs on board. You save the first analog module and still keep all 14 expansion positions. 🏭 Typical applications Pressure and flow control: connect 4 – 20 mA transmitters directly, including 2-wire sensors, and calculate the control output in your program. Inverters with analog setpoint: an analog output with 0 – 10 V or 4 – 20 mA sets the speed, the digital outputs switch enable and direction. Heating, cooling, dosing: temperature and level monitoring with limit alarms without an extra analog module. Positioning tasks: 4 pulse outputs for stepper and servo drives, three of them up to 200 kHz. ⚡ Inputs and outputs 14 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). 10 PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. 4 analog inputs: 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12-bit resolution, accuracy 0.3 % of full scale, about 30 conversions per second and channel. A red LED indicates an out-of-range value. 2 analog outputs: 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12 bit, accuracy 0.3 % of full scale, load up to 500 Ω in current mode, at least 1 kΩ in voltage mode. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs: 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. 24 V DC supply; the device provides 300 mA at 24 V for sensors. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion Two BD slots take expansion boards directly on the CPU. BD0 accepts communication and I/O boards (KB6-CAN, KB6-2COM, KB6-4DI, KB6-4DO), BD1 accepts I/O boards only (KB6-4DI, KB6-4DO). On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K606EA-30DT is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 186 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

You want to connect a machine station with sensors and valves in one go? The K523-16DT adds 8 inputs and 8 transistor outputs to your Kinco controller. ⚡ Technical data 8 digital inputs 24 V DC, wired as PNP or NPN, 3.5 mA input current, optically isolated. 8 transistor outputs in 2 groups of 4 channels, PNP, 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to None mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K623-16DT. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You want to measure temperatures in an oven, cooling circuit or barn directly with resistance thermometers, without transmitters in between? The K531-04RD reads four Pt100, Pt1000 or Cu50 sensors directly. ⚡ Technical data 4 measuring channels for Pt100 (−200 °C to +850 °C), Pt1000 (−50 °C to +300 °C) and Cu50 (−50 °C to +150 °C) as well as direct resistance (0 Ω to 2000 Ω). Connection in 2-wire or 3-wire technology. Accuracy ±0.5 °C or ±1 Ω, resolution 24 bit, about one conversion per second and channel. Diagnostics: red LED and error message to the CPU when out of range. External supply 24 V DC, at least 100 mA. Power comes via the expansion bus: the module draws up to 172 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K631-04RD. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You want to close a control loop: actual value in from the transmitter, manipulated value out to a valve or inverter? The K533-04IV provides 2 analog inputs and 2 analog outputs in one module. ⚡ Technical data 2 analog inputs for 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12 bit, accuracy 0.3 % of full scale. 2 analog outputs for 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12 bit, accuracy 0.3 % of full scale, load up to 500 Ω in current mode, above 1 kΩ in voltage mode. Conversion rate about 15 per second and channel. Diagnostics: red LED when the rated range is exceeded. External supply 24 V DC, at least 100 mA. Power comes via the expansion bus: the module draws up to 166 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K633-04IV. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You only need a few more inputs and a whole expansion module would be overkill? The KB6-4DI plugs directly onto the K6 CPU and adds four digital inputs. It fits any BD slot, so on the K606EA and K608 also BD1. ⚡ Inputs 4 digital inputs 24 V DC, wired as PNP or NPN. Input current 3.5 mA at 24 V DC, input delay below 40 µs. Optocoupler isolation with 500 V AC. Connection via terminal block with 3.81 mm pitch. 🔧 Mounting and environment The board plugs directly onto the CPU, needs no space on the DIN rail and no separate supply. A LINK LED indicates that it is seated correctly.

Two signal lamps and a valve don't justify a whole output module? The KB6-4DO plugs directly onto the K6 CPU and adds four outputs. It fits any BD slot, so on the K606EA and K608 also BD1. ⚡ Outputs 4 opto-relay outputs 24 V DC (permissible 20.4 V to 28.8 V DC), wired as PNP or NPN via the common terminal L. Output current 300 mA rated, max. 500 mA per channel, short-circuit proof and protected against switch-off peaks of inductive loads. Switching delay below 10 ms. For fast pulses, use the CPU's transistor outputs. Optocoupler isolation with 500 V AC. Connection via terminal block with 3.81 mm pitch. 🔧 Mounting and environment The board plugs directly onto the CPU, needs no space on the DIN rail and no separate supply. A LINK LED indicates that it is seated correctly.

You are missing a few inputs and outputs, for example for an additional cylinder with end position sensors? The slim K623-08DT adds 4 inputs and 4 transistor outputs to your Kinco K6. ⚡ Technical data 4 digital inputs 24 V DC, wired as PNP or NPN, 3.5 mA input current, optically isolated. 4 transistor outputs PNP, 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Output delay below 25 µs. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to 200 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals. Dimensions 50 mm × 114 mm × 70 mm (W × H × D).

Pressure, level, flow: your transmitters deliver standard signals and the CPU has no or too few analog inputs? The K531-04IV takes four current or voltage signals. ⚡ Technical data 4 analog inputs for 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, selectable per channel. Resolution 12 bit, accuracy 0.3 % of full scale, about 15 conversions per second and channel. Input limits 24 mA or 12 V, input resistance up to 500 Ω in current mode, above 4 MΩ in voltage mode. Diagnostics: red LED and error message to the CPU when out of range. External supply 24 V DC, at least 100 mA. Power comes via the expansion bus: the module draws up to 172 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K631-04IV. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You need more inputs for sensors and potential-free contacts for 230 V loads at the same time? The K623-16DR adds 8 inputs and 8 relay outputs to your Kinco K6 in one module. ⚡ Technical data 8 digital inputs 24 V DC, wired as PNP or NPN, 3.5 mA input current, optically isolated. 8 relay outputs in 2 groups of 4 channels. Switching capacity: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels. Electrical life 100 000 operations at rated load, coil/contact isolation 2000 V. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to 210 mA at 5 V and 60 mA at 24 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals. Dimensions 75 mm × 114 mm × 70 mm (W × H × D).

You need to switch contactors, solenoid valves or 230 V AC loads and the CPU outputs are not enough? The K622-16XR expands your Kinco K6 with 16 potential-free relay outputs. ⚡ Technical data 16 relay outputs in 4 groups of 4 channels. Switching capacity: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels. Electrical life 100 000 operations at rated load, coil/contact isolation 2000 V. Switching times: turn-on max. 10 ms, turn-off max. 5 ms. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to 210 mA at 5 V and 120 mA at 24 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals. Dimensions 75 mm × 114 mm × 70 mm (W × H × D).

Furnaces, extruders, hot runners: where resistance thermometers reach their limits, thermocouples keep measuring. The K531-04TC reads four thermocouples directly. ⚡ Technical data 4 measuring channels for thermocouples type J (−210 °C to +1200 °C), K (−270 °C to +1300 °C), E (−270 °C to +1000 °C) and S (−50 °C to +1600 °C). Cold junction compensation internal or external, selectable. Accuracy 0.1 % of full scale, resolution 24 bit, about one conversion per second and channel. Diagnostics: red LED and error message to the CPU when out of range. External supply 24 V DC, at least 100 mA. Power comes via the expansion bus: the module draws up to 172 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K631-04TC. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

Limit switches, light barriers and push buttons have used up your CPU inputs? The K521-16DX expands your Kinco controller with 16 digital inputs. ⚡ Technical data 16 digital inputs in 2 groups of 8 channels, 24 V DC, wired as PNP or NPN, 3.5 mA input current, optically isolated. Input delay below 40 µs. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to 210 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K621-16DX. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You want to connect servo drives, stepper drivers or CANopen I/O to your K6 without adding a gateway to the cabinet? The KB6-CAN adds a CAN interface to the CPU. It plugs into BD slot BD0. 🌐 Functions CANopen master: up to 64 slaves with 8 TPDO and 8 RPDO each, error monitoring via node guarding and heartbeat. Kinco motion protocol: simple positioning instructions for up to 16 Kinco servo and stepper drives on the CAN bus. Free CAN communication for your own telegrams. Baud rates: 10, 20, 50, 125, 500 and 800 kbit/s as well as 1 Mbit/s. Connection: RJ45 (pin 1 CAN_H, pin 2 CAN_L, pin 3 CAN_GND), built-in termination resistor switchable via DIP switch. 💡 On the K606EA and K608, only BD0 accepts communication boards; BD1 is reserved for I/O boards. 🔧 Mounting and environment The board plugs directly onto the CPU, needs no space on the DIN rail and no separate supply. A LINK LED indicates that it is seated correctly.

Two serial ports are not enough because an inverter, a barcode scanner and a scale all need to be connected? The KB6-2COM adds an RS-232 (port 0) and another RS-485 (port 3) to the K6. It plugs into BD slot BD0. 🔌 Interfaces RS-232 (port 0): Modbus RTU slave, free protocol and programming, for example for scanners, printers or an older panel. RS-485 (port 3): Modbus RTU master or slave and programming. Baud rate: 1200 to 115 200 bit/s. Connection: shared DB9 connector. RS-232 on pins 2 (RxD), 3 (TxD) and 5 (GND), RS-485 on pins 1 (B) and 6 (A). 💡 On the K606EA and K608, only BD0 accepts communication boards. 🔧 Mounting and environment The board plugs directly onto the CPU, needs no space on the DIN rail and no separate supply. A LINK LED indicates that it is seated correctly.

Your K6 has more expansion modules than its own bus supply can carry? The K680 (also PS680) feeds fresh 5 V and 24 V into the expansion bus. All modules after the K680 are powered by it, all modules before it by the CPU. ⚡ Technical data Input: 85 to 265 V AC. Output to the bus: up to 1000 mA at 5 V (logic supply) and up to 250 mA at 24 V (relay drive). Plug & play: uses no CPU memory and does not need to be configured in KincoBuilder. Status indication: PW LED. 💡 How to plan the current budget The K6 CPU provides 1500 mA at 5 V and 360 mA at 24 V. Add up the bus consumption of your modules, for example 210 mA for a K621-16DX, or 210 mA and 120 mA for a K622-16XR. When the budget gets tight, you place the K680 at the right position in the module row. Kinco generally recommends it from 7 expansion modules. Make sure the K680 and the CPU are fed from the same supply. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals. Dimensions 75 mm × 114 mm × 70 mm (W × H × D).

Valve terminals, signal lamps and auxiliary contactors need more outputs than your CPU has? The K522-16DT expands your Kinco controller with 16 transistor outputs. ⚡ Technical data 16 transistor outputs in 4 groups of 4 channels, PNP, 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Output delay below 25 µs. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to 240 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K622-16DT. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.