For anyone looking to equip a machine or system with both a user interface and control logic without wiring two separate devices (HMI and PLC), the Kinco MK070E-33DT offers a compact all-in-one solution: controller and 7" touch panel in a single housing, configured together and factory-matched to each other. This saves space in the control cabinet, simplifies commissioning and reduces potential failure points compared to separate systems. 🏭 Typical Applications Simple to mid-range machine control: Conveyor systems, mixing machines, packaging lines or test stands – wherever control logic and operator interface need to share the same device and space in the control cabinet is limited. Retrofit projects: Replace legacy PLC systems without sourcing an additional external HMI. The MK device handles both and communicates via Modbus RTU with existing drives, sensors and peripherals. OEM machine builders with IoT requirements: The built-in Kinco IoT client enables remote download and VNC remote access without additional hardware – useful for service engineers maintaining machines at customer sites remotely. Expandable small controllers: Connect up to 8 KS expansion modules (digital, analog, temperature) via the integrated CAN bus when the on-board I/O is not sufficient. 🖥️ Display and Touch 7" TFT display, 800 × 480 pixels, 256K colors – sufficient resolution for clear process visualizations, trend curves and alarm screens. LED backlight with 50,000 hours lifespan (approx. 5.7 years continuous operation). HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2 – adequate reserve for complex project files and recipe data. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments The MK070E-33DT features a 4-wire resistive touchscreen. Operation works reliably even with safety gloves or slightly wet fingers – no capacitive sensor that depends on skin conductivity. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45): HMI configuration over the network, remote access via KDManager. Factory default IP: 192.168.0.252. 2 × RS485 (Port1 + Port2, DB9): Port1 supports Modbus RTU master/slave, programming and free communication. Port2 supports Modbus RTU and free communication – ideal for a second fieldbus segment (e.g. drive on Port1, barcode scanner on Port2). Max. 115,200 bps, up to 32 nodes per channel. CAN bus (DB9): Connect up to 8 KS expansion modules (digital I/O, analog I/O, temperature). USB host (Type-A): USB flash drive, keyboard or mouse. USB slave (USB-B): Program download from PC via KincoBuilder / KincoDTools. 🌐 IoT and Remote Access For anyone who needs to maintain machines at customer sites without traveling on-site, the built-in Kinco IoT client provides remote download of new HMI projects, transparent PLC access (Kinco Transparent PLC) for diagnostics and parameter changes, and VNC monitoring of operator screens – all without additional routers or gateway hardware. 💡 Requirements: network connection for the device and a Kinco IoT account (free). Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools The MK device is configured using two free software tools: KincoBuilder (PLC programming, IEC 61131-3): Supports Ladder Diagram (LD) and Instruction List (IL). Includes a motion control wizard for positioning tasks, HSC wizard (high-speed counters, 4 × up to 50 kHz) and an offline simulator with single-step execution and breakpoints. Free download at en.kinco.cn. KincoDTools (HMI configuration): Same platform as the Kinco M2 series and the classic Kinco Green Series (V1). Supports offline simulation, macros (C language) and up to 32,768 screens. 💡 Note for Modbus users: The MK communicates via Port1 as Modbus RTU master with Kinco drives (KC100, KC200, GD28 and others) as well as drives from other manufacturers – provided they support Modbus RTU slave. 🏷️ Manufacturer and Reliability Kinco Automation is an established manufacturer with extensive experience developing HMI, PLC and drive technology for the global industrial market. The MK070E-33DT is CE certified and carries the RoHS and EAC markings. EMC requirements for industrial use in Europe are met (IEC 61131-2). Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout dimensions 192 × 138 mm, mounting depth 34 mm. Horizontal and vertical installation supported (configurable in KincoDTools). Mounted with 4 included mounting clips; recommended torque 0.5 N·m. Overall dimensions: 204 × 150 × 34 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W. Scope of delivery: MK070E-33DT, 4 × mounting clips with screws, detachable terminal blocks pre-installed.

For anyone looking for a compact all-in-one solution for simple to mid-range machine control, the Kinco MK043E-20DT combines a 4.3" touch panel and PLC controller in a single housing. Particularly suited for applications where the panel cutout is restricted and a 7" display would be unnecessarily large – without making significant compromises on I/O capacity or connectivity. 🏭 Typical Applications Small machines and compact systems: Conveyors, dosing systems, mixing stations or refrigeration units with limited cabinet space – the MK043E-20DT fits controller and operator panel into a 119 × 93 mm panel cutout. Retrofit and replacement: Replace legacy controllers with separate operator panels using a single compact unit. The device communicates via Modbus RTU with existing drives, sensors and actuators. Expandable solutions: Connect up to 8 KS expansion modules via CAN bus when 9 DI + 9 DO + 2 AI is not enough. 🖥️ Display and Touch 4.3" TFT display, 480 × 272 pixels, 256K colors – sufficient for simple process displays, setpoint entry and status messages. LED backlight with 50,000 hours lifespan. HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments Like all MK devices, the MK043E-20DT uses a 4-wire resistive touchscreen. Operation with safety gloves or slightly wet fingers is straightforward. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45) – network download and remote access via KDManager. 2 × RS485 (Port1 + Port2) – Modbus RTU master/slave, programming, free communication. Max. 115,200 bps. CAN bus – up to 8 KS expansion modules. USB host (Type-A) + USB slave (USB-B). 🌐 IoT and Remote Access Built-in Kinco IoT client for remote download, transparent PLC access and VNC monitoring. Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools KincoBuilder – IEC 61131-3: LD and IL. Motion control and HSC wizard (4 × HSC up to 50 kHz), offline simulator. Free download at en.kinco.cn. KincoDTools – HMI configuration, same platform as the Kinco F2 HMI series. 🏷️ Manufacturer and Reliability Kinco Automation is an established manufacturer with extensive experience developing HMI, PLC and drive technology for the global industrial market. The MK043E-20DT is CE certified and carries the RoHS and EAC markings. Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout dimensions 119 × 93 mm, mounting depth 32 mm. Overall dimensions: 132 × 102 × 32 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W.

💡 This version is supplied with a neutral front panel without Kinco branding – ideal for OEM applications under your own brand name. For anyone who needs maximum I/O flexibility in a compact 4.3" all-in-one, the Kinco MK043E-27DT is the most versatile variant of the MK043 series: 4 bidirectional DIO channels freely configurable as DI or DO by wiring alone, a USB-C programming port (standard phone data cable sufficient) and an additional RS232 port on the front panel – alongside 10 DI, 10 DO, 2 AI, 1 AO and full Ethernet/IoT connectivity. 🏭 Typical Applications Flexible I/O applications: Use the 4 DIO channels as additional inputs or outputs depending on the application – no software reconfiguration, just rewire. Ideal for machines with varying sensor/actuator configurations. Applications requiring RS232: Connect legacy devices, barcode readers or serial printers directly via the front-mounted RS232 port (COM2) – without occupying the RS485 ports. Mobile commissioning: USB-C port on the front accepts standard phone data cables – no special programming cable required for PLC and HMI downloads. 🖥️ Display and Touch 4.3" TFT display, 480 × 272 pixels, 256K colors. LED backlight 50,000 hours. HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments 4-wire resistive touchscreen. Operation with safety gloves or slightly wet fingers is straightforward. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45). Factory default IP: 192.168.0.252. 2 × RS485 (Port1 + Port2) + RS232 (COM2, front panel). Modbus RTU master/slave on Port1. Max. 115,200 bps. CAN bus: Up to 8 KS expansion modules. USB host (Type-A) + USB slave (USB-C). 🌐 IoT and Remote Access Built-in Kinco IoT client for remote download, transparent PLC access and VNC monitoring. Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools KincoBuilder – IEC 61131-3: LD and IL. Motion control and HSC wizard. Free download at en.kinco.cn. KincoDTools – HMI configuration. 🏷️ Manufacturer and Reliability The MK043E-27DT is CE certified and carries the RoHS and EAC markings. Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout 119 × 93 mm, mounting depth 45.42 mm. Scope of delivery: MK043E-27DT-Blank (neutral front panel), 4 × mounting clips with screws, detachable terminal blocks pre-installed. ⚠️ Note: The MK043E-27DT is 14 mm deeper than other MK043 models – verify available installation depth before ordering. Overall dimensions: 132 × 102 × 45.42 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W.

You need a controller for a machine with a manageable number of signals and want to expand later without replacing the PLC? The Kinco K606-24 comes with 14 digital inputs, 10 outputs, Ethernet and two galvanically isolated RS-485 ports, and grows with your system via one BD slot and up to 14 expansion modules. 🏭 Typical applications Conveying and packaging: belts, diverters and feeders. The high-speed counters read encoders up to 200 kHz directly on the device. Positioning with stepper or servo drives: the transistor variants output pulse and direction on four channels, three of them up to 200 kHz. Pumps, fans and frequency inverters: control drives and meters directly via Modbus RTU on RS-485. Connection to HMI and control system: Modbus TCP via Ethernet, for example to a Kinco HMI or a higher-level SCADA. ⚙️ Four variants K606-24DT: 24 V DC supply, 10 PNP transistor outputs K606-24AT: 100 – 240 V AC supply, 10 PNP transistor outputs K606-24DR: 24 V DC supply, 10 relay outputs K606-24AR: 100 – 240 V AC supply, 10 relay outputs 💡 The relay variants have no pulse outputs. For positioning tasks, choose DT or AT. ⚡ Inputs and outputs 14 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Relay outputs: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels, electrical life 100 000 operations at rated load. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs (transistor variants only): 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. Positioning instructions and a follow function are included in KincoBuilder. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion One BD slot takes an expansion board directly on the CPU: KB6-CAN (CANopen master), KB6-2COM (RS-232 + RS-485), KB6-4DI or KB6-4DO. On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K606-24 is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 128 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

4 analog inputs (4 - 20 mA, 0 - 10 V), resolution 12 bit, sampling rate 15 Hz. 2 analog outputs (4 - 20 mA, 0 - 10 V), resolution 12 bit, update rate 15 Hz 1 x RS-485 (Modbus RTU) + expansion ports for KS105 This extension is compatible with Kinco KS105 PLC. However, it can also be used independently as a Modbus RTU analog I/O module.   

With this extension cable, the devices of the MK series from Kinco, a combination device of HMI and PLC can be connected with the extensions. The extensions he Kinco KS-PLC series can be used so easily with the MK series. Internally MK-PLC and extension are connected via a CAN protocol, but this does not need to be programmed, it is sufficient to configure the extensions in the hardware configuration of the PLC in Kinco Builder.On the last extension should be activated via the DIP switches the end resistor.The extension cable is high quality with metal connector on HMI PLC side. In addition, the two RS-485 interfaces of MK-PLC are via a connector with screw contacts. This can be used to connect other Modbus devices or serial devices to MK-PLC.This cable is a service product for easier connection. You can also easily assemble your own cable for the extension. You can find the correct PIN assignment in the product photos.

8 Digital Inputs 24 VDC (PNP)8 Digital Outputs Transistor 24 VDC1 Analog Input 4 - 20 mA / 0 - 10 V1 Analog Output 4 - 20 mA / 0 - 10 V

💡 This version is supplied with a neutral front panel without Kinco branding – ideal for OEM applications under your own brand name. For anyone looking to equip a machine or system with both a user interface and control logic without wiring two separate devices (HMI and PLC), the Kinco MK070E-33DT offers a compact all-in-one solution: controller and 7" touch panel in a single housing, configured together and factory-matched to each other. This saves space in the control cabinet, simplifies commissioning and reduces potential failure points compared to separate systems. 🏭 Typical Applications Simple to mid-range machine control: Conveyor systems, mixing machines, packaging lines or test stands – wherever control logic and operator interface need to share the same device and space in the control cabinet is limited. Retrofit projects: Replace legacy PLC systems without sourcing an additional external HMI. The MK device handles both and communicates via Modbus RTU with existing drives, sensors and peripherals. OEM machine builders with IoT requirements: The built-in Kinco IoT client enables remote download and VNC remote access without additional hardware – useful for service engineers maintaining machines at customer sites remotely. Expandable small controllers: Connect up to 8 KS expansion modules (digital, analog, temperature) via the integrated CAN bus when the on-board I/O is not sufficient. 🖥️ Display and Touch 7" TFT display, 800 × 480 pixels, 256K colors – sufficient resolution for clear process visualizations, trend curves and alarm screens. LED backlight with 50,000 hours lifespan (approx. 5.7 years continuous operation). HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2 – adequate reserve for complex project files and recipe data. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments The MK070E-33DT features a 4-wire resistive touchscreen. Operation works reliably even with safety gloves or slightly wet fingers – no capacitive sensor that depends on skin conductivity. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45): HMI configuration over the network, remote access via KDManager. Factory default IP: 192.168.0.252. 2 × RS485 (Port1 + Port2, DB9): Port1 supports Modbus RTU master/slave, programming and free communication. Port2 supports Modbus RTU and free communication – ideal for a second fieldbus segment (e.g. drive on Port1, barcode scanner on Port2). Max. 115,200 bps, up to 32 nodes per channel. CAN bus (DB9): Connect up to 8 KS expansion modules (digital I/O, analog I/O, temperature). USB host (Type-A): USB flash drive, keyboard or mouse. USB slave (USB-B): Program download from PC via KincoBuilder / KincoDTools. 🌐 IoT and Remote Access For anyone who needs to maintain machines at customer sites without traveling on-site, the built-in Kinco IoT client provides remote download of new HMI projects, transparent PLC access (Kinco Transparent PLC) for diagnostics and parameter changes, and VNC monitoring of operator screens – all without additional routers or gateway hardware. 💡 Requirements: network connection for the device and a Kinco IoT account (free). Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools The MK device is configured using two free software tools: KincoBuilder (PLC programming, IEC 61131-3): Supports Ladder Diagram (LD) and Instruction List (IL). Includes a motion control wizard for positioning tasks, HSC wizard (high-speed counters, 4 × up to 50 kHz) and an offline simulator with single-step execution and breakpoints. Free download at en.kinco.cn. KincoDTools (HMI configuration): Same platform as the Kinco M2 series and the classic Kinco Green Series (V1). Supports offline simulation, macros (C language) and up to 32,768 screens. 💡 Note for Modbus users: The MK communicates via Port1 as Modbus RTU master with Kinco drives (KC100, KC200, GD28 and others) as well as drives from other manufacturers – provided they support Modbus RTU slave. 🏷️ Manufacturer and Reliability Kinco Automation is an established manufacturer with extensive experience developing HMI, PLC and drive technology for the global industrial market. The MK070E-33DT is CE certified and carries the RoHS and EAC markings. EMC requirements for industrial use in Europe are met (IEC 61131-2). Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout dimensions 192 × 138 mm, mounting depth 34 mm. Horizontal and vertical installation supported (configurable in KincoDTools). Mounted with 4 included mounting clips; recommended torque 0.5 N·m. Overall dimensions: 204 × 150 × 34 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W. Scope of delivery: MK070E-33DT-Blank (neutral front panel), 4 × mounting clips with screws, detachable terminal blocks pre-installed.

16 digital input (24 VDC)   1 x RS-485 (Modbus RTU) + expansion port for KS105 This extension is compatible with Kinco KS105 PLC. However, it can also be used independently as a Modbus RTU analog I/O module.   

22 digital inputs 24 VDC (PNP) 8 digital outputs transistor 24 VDC12 digital outputs relay2 x RS-485 (supports Modbus RTU) Programming Software: Kinco Builder (English, Ladder Diagram KOP / AWL, free download) Programming you can the Kinco K2 with the free Kinco-Builder programming software (available as download a little further down this page).   Scope of delivery: PLC  

4 temperature inputs (PT100, PT1000, Cu50 or resistor) 1 x RS-485 (Modbus RTU) + expansion ports for KS105 This extension is compatible with the Kinco KS105 PLC and the MK070E. However, it can also be used independently as a Modbus RTU analog I/O module.  Measuring ranges:Pt100: -200 to +850 °CCu50:  -50 to +150°CPt1000: -50to +300 °CResistance: 0 to 2000Ω

8 Digital input (24 VDC)  6 relay output (230 VAC, 2A)  1 x RS-485 (Modbus RTU) + expansion port for KS105 This extension is compatible with Kinco KS105 PLC. However, it can also be used independently as a Modbus RTU analog I/O module.   

8 digital inputs 24 VDC (PNP) 8 digital outputs transistor 24 VDC 1 x RS-485 (Modbus RTU) + 1 x RS-232 (programming port) You can program this compact Kinco KS-PLC with the free Kinco-Builder programming software (available as download a little further down on this page).   Scope of delivery: PLC  

Your system has more sensors and actuators than a compact PLC with 24 channels can handle? The Kinco K608-40 comes with 24 digital inputs and 16 outputs, plus two BD slots for CAN, additional interfaces or I/O. Many machines manage without a single expansion module. 🏭 Typical applications Multi-station machines: assembly, test and packaging lines with many limit switches, light barriers and valves. Drives via CANopen: with the KB6-CAN board you control up to 64 CANopen nodes, or Kinco servo and stepper drives via the Kinco motion protocol. Positioning: the transistor variants output pulse and direction on four channels, three of them up to 200 kHz. Building services: pumps, ventilation and inverters via Modbus RTU, visualisation via Modbus TCP. ⚙️ Four variants K608-40DT: 24 V DC supply, 16 PNP transistor outputs K608-40AT: 100 – 240 V AC supply, 16 PNP transistor outputs K608-40DR: 24 V DC supply, 16 relay outputs K608-40AR: 100 – 240 V AC supply, 16 relay outputs 💡 The relay variants have no pulse outputs. For positioning tasks, choose DT or AT. ⚡ Inputs and outputs 24 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Relay outputs: 2 A per contact at 30 V DC or 250 V AC, max. 8 A per group of 4 channels, electrical life 100 000 operations at rated load. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs (transistor variants only): 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. Positioning instructions and a follow function are included in KincoBuilder. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion Two BD slots take expansion boards directly on the CPU. BD0 accepts communication and I/O boards (KB6-CAN, KB6-2COM, KB6-4DI, KB6-4DO), BD1 accepts I/O boards only (KB6-4DI, KB6-4DO). On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K608-40 is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 186 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

12 relay output (230 VAC, 2A)  1 x RS-485 (Modbus RTU) + expansion port for KS105 This extension is compatible with Kinco KS105 PLC. However, it can also be used independently as a Modbus RTU analog I/O module.   

6 digital inputs 24 VDC (PNP)6 digital outputs transistor 24 VDC4 connectors that can be used as digital input

For anyone who needs maximum I/O flexibility in a compact 4.3" all-in-one, the Kinco MK043E-27DT is the most versatile variant of the MK043 series: 4 bidirectional DIO channels freely configurable as DI or DO by wiring alone, a USB-C programming port (standard phone data cable sufficient) and an additional RS232 port on the front panel – alongside 10 DI, 10 DO, 2 AI, 1 AO and full Ethernet/IoT connectivity. 🏭 Typical Applications Flexible I/O applications: Use the 4 DIO channels as additional inputs or outputs depending on the application – no software reconfiguration, just rewire. Ideal for machines with varying sensor/actuator configurations. Applications requiring RS232: Connect legacy devices, barcode readers or serial printers directly via the front-mounted RS232 port (COM2) – without occupying the RS485 ports. Mobile commissioning: USB-C port on the front accepts standard phone data cables – no special programming cable required for PLC and HMI downloads. 🖥️ Display and Touch 4.3" TFT display, 480 × 272 pixels, 256K colors. LED backlight 50,000 hours. HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments 4-wire resistive touchscreen. Operation with safety gloves or slightly wet fingers is straightforward. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45). Factory default IP: 192.168.0.252. 2 × RS485 (Port1 + Port2) + RS232 (COM2, front panel). Modbus RTU master/slave on Port1. Max. 115,200 bps. CAN bus: Up to 8 KS expansion modules. USB host (Type-A) + USB slave (USB-C). 🌐 IoT and Remote Access Built-in Kinco IoT client for remote download, transparent PLC access and VNC monitoring. Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools KincoBuilder – IEC 61131-3: LD and IL. Motion control and HSC wizard. Free download at en.kinco.cn. KincoDTools – HMI configuration. 🏷️ Manufacturer and Reliability The MK043E-27DT is CE certified and carries the RoHS and EAC markings. Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout 119 × 93 mm, mounting depth 45.42 mm. ⚠️ Note: The MK043E-27DT is 14 mm deeper than other MK043 models – verify available installation depth before ordering. Overall dimensions: 132 × 102 × 45.42 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W.

The Kinco K6S series PLC is a compact modular PLC.

💡 This version is supplied with a neutral front panel without Kinco branding – ideal for OEM applications under your own brand name. For anyone looking for a compact all-in-one solution for simple to mid-range machine control, the Kinco MK043E-20DT combines a 4.3" touch panel and PLC controller in a single housing. Particularly suited for applications where the panel cutout is restricted and a 7" display would be unnecessarily large – without making significant compromises on I/O capacity or connectivity. 🏭 Typical Applications Small machines and compact systems: Conveyors, dosing systems, mixing stations or refrigeration units with limited cabinet space – the MK043E-20DT fits controller and operator panel into a 119 × 93 mm panel cutout. Retrofit and replacement: Replace legacy controllers with separate operator panels using a single compact unit. The device communicates via Modbus RTU with existing drives, sensors and actuators. Expandable solutions: Connect up to 8 KS expansion modules via CAN bus when 9 DI + 9 DO + 2 AI is not enough. 🖥️ Display and Touch 4.3" TFT display, 480 × 272 pixels, 256K colors – sufficient for simple process displays, setpoint entry and status messages. LED backlight with 50,000 hours lifespan. HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments Like all MK devices, the MK043E-20DT uses a 4-wire resistive touchscreen. Operation with safety gloves or slightly wet fingers is straightforward. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45) – network download and remote access via KDManager. 2 × RS485 (Port1 + Port2) – Modbus RTU master/slave, programming, free communication. Max. 115,200 bps. CAN bus – up to 8 KS expansion modules. USB host (Type-A) + USB slave (USB-B). 🌐 IoT and Remote Access Built-in Kinco IoT client for remote download, transparent PLC access and VNC monitoring. Configure in KincoDTools under [IOT]. 🔗 Programming: KincoBuilder + KincoDTools KincoBuilder – IEC 61131-3: LD and IL. Motion control and HSC wizard (4 × HSC up to 50 kHz), offline simulator. Free download at en.kinco.cn. KincoDTools – HMI configuration, same platform as the Kinco F2 HMI series. 🏷️ Manufacturer and Reliability Kinco Automation is an established manufacturer with extensive experience developing HMI, PLC and drive technology for the global industrial market. The MK043E-20DT is CE certified and carries the RoHS and EAC markings. Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout dimensions 119 × 93 mm, mounting depth 32 mm. Scope of delivery: MK043E-20DT-Blank (neutral front panel), 4 × mounting clips with screws, detachable terminal blocks pre-installed. Overall dimensions: 132 × 102 × 32 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W.

Your machine needs to measure pressures, temperatures or levels and drive an inverter via an analog signal, not just switch? The Kinco K606EA-30DT already has 4 analog inputs and 2 analog outputs on board. You save the first analog module and still keep all 14 expansion positions. 🏭 Typical applications Pressure and flow control: connect 4 – 20 mA transmitters directly, including 2-wire sensors, and calculate the control output in your program. Inverters with analog setpoint: an analog output with 0 – 10 V or 4 – 20 mA sets the speed, the digital outputs switch enable and direction. Heating, cooling, dosing: temperature and level monitoring with limit alarms without an extra analog module. Positioning tasks: 4 pulse outputs for stepper and servo drives, three of them up to 200 kHz. ⚡ Inputs and outputs 14 digital inputs 24 V DC, wired as PNP or NPN, optically isolated, input delay below 40 µs (high-speed channels below 5 µs). 10 PNP transistor outputs: 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. 4 analog inputs: 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12-bit resolution, accuracy 0.3 % of full scale, about 30 conversions per second and channel. A red LED indicates an out-of-range value. 2 analog outputs: 4 – 20 mA, 0 – 20 mA, 1 – 5 V and 0 – 10 V, 12 bit, accuracy 0.3 % of full scale, load up to 500 Ω in current mode, at least 1 kΩ in voltage mode. High-speed counters: 4 channels, HSC0 and HSC1 up to 200 kHz, HSC2 and HSC3 up to 20 kHz single-phase or 10 kHz A/B. 4 edge interrupts on I0.0 to I0.3. Pulse outputs: 4 channels for PTO (pulse/direction) and PWM, PTO0 to PTO2 up to 200 kHz, PTO3 up to 10 kHz. 24 V DC supply; the device provides 300 mA at 24 V for sensors. 🔌 Communication Ethernet 10/100 Mbit/s: Modbus TCP client and server, free communication via TCP and UDP, program upload/download and firmware update over the network. 2 × RS-485, galvanically isolated: 1200 to 115 200 bit/s, Modbus RTU master or slave, free protocol and programming on both ports. Up to 32 devices per port. 🧩 Expansion Two BD slots take expansion boards directly on the CPU. BD0 accepts communication and I/O boards (KB6-CAN, KB6-2COM, KB6-4DI, KB6-4DO), BD1 accepts I/O boards only (KB6-4DI, KB6-4DO). On top, up to 14 expansion modules connect to the local bus. The CPU supplies them with up to 1500 mA at 5 V and 360 mA at 24 V. From about 7 modules, or when the current budget runs out, you add the K680 power supply to the module row. 💻 Programming and memory You program the controller with KincoBuilder (IEC 61131-3) in ladder diagram (LD) or instruction list (IL), version V8.5.0.3 or later. The CPU offers 8k instructions of program memory and 20 kB of data memory (16 kB V area, 4 kB M area). 1000 standard instructions execute in 0.3 ms. On top come 256 timers, 256 counters, arrays with up to 1024 elements and a battery-backed real-time clock (deviation below 5 min per month at 25 °C). The V area and counter values are retained on power loss, and the battery is replaceable. 🔗 Compatible with Kinco K5 Terminal layout and power connection match the K5 series, existing K5 programs run without changes, and K5 expansion modules plug in directly. This lets you replace a K5 in the cabinet without rewiring or reprogramming. 🏷️ Manufacturer and standards Kinco Automation, based in Shanghai and Shenzhen, develops controllers, HMIs and drive technology for international machine builders. The K606EA-30DT is CE marked (EN IEC 61000-6-2:2019, EN IEC 61000-6-4:2019) and tested to GB/T 15969.3-2007, which is equivalent to IEC 61131-2:2007. Protection class IP20, operation from −10 °C to +55 °C, 10 % – 95 % relative humidity without condensation, altitude up to 2000 m. 🔧 Mounting On 35 mm DIN rail or with M4 screws on the mounting plate. Dimensions 186 mm × 114 mm × 76 mm, the terminal blocks are pluggable.

14 transistor outputs (24 VDC PNP) 1 x RS-485 (Modbus RTU) + expansion port for KS105 This extension is compatible with Kinco KS105 PLC. However, it can also be used independently as a Modbus RTU analog I/O module.   

For temperature control applications that require direct measurement of resistance temperature detectors without a separate transmitter module, the Kinco MK070E-27DRT integrates 3 RTD inputs (Pt100, Cu50, Pt1000) directly into a 7" HMI+PLC device – alongside 12 DI, 12 relay outputs and full Ethernet connectivity. 🏭 Typical Applications Temperature control systems: Heating, drying, cooling or process temperature regulation where Pt100 or Pt1000 sensors are already installed. No additional analog input module required. Retrofitting temperature monitoring: Replace standalone temperature controllers with an integrated HMI+PLC solution that shows temperature trends, alarms and setpoints on the built-in 7" display. Relay-switched process control: 12 relay outputs for switching heating elements, contactors or valves at AC 250 V or DC 30 V. 🖥️ Display and Touch 7" TFT display, 800 × 480 pixels, 256K colors. LED backlight 50,000 hours. HMI CPU: 700 MHz RISC, 128 MB Flash + 64 MB DDR2. 🧤 Resistive Touch: Suitable for Gloves and Industrial Environments The MK070E-27DRT features a 4-wire resistive touchscreen. Operation works reliably even with safety gloves or slightly wet fingers. 🌡️ RTD Temperature Inputs 3 × RTD input channels – support Pt100 (-200 to +850 °C), Cu50 (-50 to +150 °C) and Pt1000 (-50 to +300 °C) as well as resistance measurement (0–2,000 Ω). 2-wire and 3-wire RTD wiring supported. Unused channels must be short-circuited. 🔌 Connectivity and Interfaces Ethernet 10/100M (RJ45). Factory default IP: 192.168.0.252. 2 × RS485 (Port1 + Port2): Modbus RTU master/slave. Max. 115,200 bps. CAN bus: Up to 8 KS expansion modules. USB host (Type-A) + USB slave (USB-B). 🌐 IoT and Remote Access Built-in Kinco IoT client for remote download, transparent PLC access and VNC monitoring. 🔗 Programming: KincoBuilder + KincoDTools KincoBuilder – IEC 61131-3: LD and IL. Free download at en.kinco.cn. KincoDTools – HMI configuration. ⚠️ Note: Relay outputs do NOT support high-speed pulse output (PTO/PWM). 🏷️ Manufacturer and Reliability Kinco Automation is an established manufacturer with extensive experience in HMI, PLC and drive technology. The MK070E-27DRT is CE certified and carries RoHS and EAC markings. Kinco devices are deployed at well over 100 spstiger customers across Germany. 🔧 Mounting and Scope of Delivery Panel mount: Cutout 192 × 138 mm, depth 34 mm. 4 mounting clips included. Overall dimensions: 204 × 150 × 34 mm. Power supply: DC 24 V (20.4–28.8 V), max. 10 W.

You want to connect a machine station with sensors and valves in one go? The K523-16DT adds 8 inputs and 8 transistor outputs to your Kinco controller. ⚡ Technical data 8 digital inputs 24 V DC, wired as PNP or NPN, 3.5 mA input current, optically isolated. 8 transistor outputs in 2 groups of 4 channels, PNP, 500 mA per channel at 24 V DC, protected against short circuit, inductive loads and reverse polarity. Status indication via green LED per channel. Power comes via the expansion bus: the module draws up to None mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K623-16DT. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.

You want to measure temperatures in an oven, cooling circuit or barn directly with resistance thermometers, without transmitters in between? The K531-04RD reads four Pt100, Pt1000 or Cu50 sensors directly. ⚡ Technical data 4 measuring channels for Pt100 (−200 °C to +850 °C), Pt1000 (−50 °C to +300 °C) and Cu50 (−50 °C to +150 °C) as well as direct resistance (0 Ω to 2000 Ω). Connection in 2-wire or 3-wire technology. Accuracy ±0.5 °C or ±1 Ω, resolution 24 bit, about one conversion per second and channel. Diagnostics: red LED and error message to the CPU when out of range. External supply 24 V DC, at least 100 mA. Power comes via the expansion bus: the module draws up to 172 mA at 5 V. A K6 CPU provides a total of 1500 mA at 5 V and 360 mA at 24 V. If the budget is not enough for your module row, you insert the K680 power supply. 💡 Expansion module of the Kinco K5 series. It works with K5 CPUs and directly with all K6 CPUs (K606, K606EA, K608), whose expansion bus is compatible with the K5. Technically it corresponds to the K6 module K631-04RD. 🔧 Mounting and environment Protection class IP20, operation from −10 °C to +55 °C, CE marked. Mounting on 35 mm DIN rail or with M4 screws, connection via screw terminals.