Kinco G2100H-CTP 10.1" Industrial Touch Monitor 1280 × 800 with HDMI, VGA and USB-C
If you want to operate a machine or plant from a separate computer, an industrial PC board or an HMI without a display, you only need one thing: a rugged touch display that fits into the control cabinet door. That is exactly what the Kinco G2100H-CTP is — a 10.1" industrial touch monitor in a metal housing with 1280 × 800 pixels, capacitive multi-touch and IP65 front protection.
⚠️ Important classification note: The G2100H-CTP is not an HMI. It has no control logic, no PLC drivers and no configuration software — it displays what another source provides and returns touch input via USB-C. If you are looking for a programmable operator panel, see the Kinco G2100E of the G2 series.
🏭 Typical applications
Operator interface for an industrial PC: The iPC sits inside the cabinet, the interface sits in the door. HDMI and USB-C are enough for image and touch — no additional driver required.
Display for an HMI without a screen: Combined with the Kinco xF-SiHMI01 you get a two-part operator panel: processing unit on the DIN rail, display in the door.
Second operator station on an existing plant: Mirror an existing signal at a second location without a second licence or a second project.
Display for Raspberry Pi and single-board computers: HDMI output, USB-C for touch, 24 V DC from the cabinet supply.
🖥️ Display
10.1" TFT with a 217 mm × 135 mm active area and 1280 × 800 pixels (16:10)
16.7 million colours, contrast ratio 1000:1, brightness 280 cd/m²
Viewing angle 80° / 80° / 80° / 80° (left / right / up / down)
LED backlight with a rated life of 30,000 hours
👆 Capacitive multi-touch
The touch panel is capacitive and multi-finger capable — swiping, zooming and scrolling work just like on a tablet. Touch data is returned via the USB-C port and registers on the computer as a standard input device, without driver installation.
⚠️ Important note: Thick protective gloves or wet fingers can impair detection. If you work with gloves, a resistive operator panel is the better choice.
🔌 Connections
1 × HDMI (1.3) — digital video signal
1 × VGA — analogue video signal for older sources
1 × USB Type-C — touch feedback
3-pin screw terminal block — FG / GND / DC 24 V
Video processing is handled by a Realtek single-chip monitor IC. All connections are located on a single strip at the rear.
🔧 Mounting and environment
Rear panel mounting into a 192 mm × 138 mm cut-out, fixed with mounting clamps
Outer dimensions 250 mm × 169 mm × 33 mm, weight 1.2 kg
Metal housing, passive cooling without a fan
IP65 front protection (4208-93), conformal coated PCB for harsh environments
Operation -10 °C to +50 °C, storage -20 °C to +60 °C, humidity 10 – 90 % non-condensing
Supply 18 – 28 V DC, 15 W at 24 V, power interruptions of up to 3 ms are bridged
Vibration tested at 10 – 500 Hz, 30 m/s², one hour each in X, Y and Z direction
🏷️ Manufacturer and reliability
Kinco Automation is an established manufacturer with years of experience in developing HMI and drive technology for the global industrial market. The G2100H-CTP is CE certified (EN 61000-6-4:2007+A1:2011, EN 61000-6-2:2005), withstands 500 V AC test voltage for one minute and reaches an insulation resistance of more than 50 MΩ at 500 V DC. Kinco devices are in use at well over 100 spstiger customers in Germany.
💡 A comparable monitor with Full HD and considerably higher brightness is the Lilliput TK1019/T with 1920 × 1200 pixels and 1500 cd/m².
- Available
- Delivery Time : 2-5 days
Tip
New
Lilliput 7" TK701.T Touch Monitor with HDMI connection 1000 Nits IP65
If you need a small, rugged operator surface in a control cabinet, an operator desk or a vehicle — without buying an industrial PC that comes with its own display — the Lilliput TK701/T is the most compact entry point into the TK series.🏭 Typical applicationsCompact operator panel: Seven inches are enough for status display, setpoint entry and acknowledgement. It replaces a row of pushbuttons without rebuilding the cabinet.Vehicle and construction machinery: The 12 to 24 V DC input range covers the on-board supply directly — no converter needed. Operation down to -20 °C.Retrofit on existing machinery: An HDMI output on the existing controller is all it takes. Touch is reported as a USB mouse, so no drivers have to be installed.Second screen at test stations: Two AV inputs in addition to HDMI and VGA — even older analogue sources such as inspection cameras connect directly.🖥️ Display7" LCD with 800 × 480 pixelsBrightness 1000 cd/m² (nits) — sunlight readableContrast 1000:1, viewing angle 140° / 120° (horizontal / vertical)👆 10-point capacitive touchThe capacitive touch responds to a light touch and supports multi-touch gestures such as zooming and scrolling. It is reported to the computer as a standard input device — no drivers need to be installed.💡 A capacitive touch is only partly suitable for use with thick protective gloves. If that is a requirement, the TK1331/T, TK1850/T, TK2380/T and TK2700/T models offer an explicitly glove-capable version.🔌 ConnectionsThe unit is a pure monitor without its own CPU. The image comes from a PC, industrial PC or controller; touch is returned via USB.HDMI 1.4bVGA2× AV (composite)3.5 mm audio input3.5 mm headphone outputUSB-A for the touch functionUSB-A for firmware updatesOnly of limited use with a Kinco xF-SiHMI — its output is 1920 × 1080 while the panel shows 800 × 480. Well suited to industrial PCs and Raspberry Pi with adjustable resolution.🔧 Mounting and scope of deliveryNo VESA hole pattern. Four wall-mount slots in the housing and four fixing screws are included; for panel mounting the unit is inserted from the front and clamped at the sides.Outer dimensions 210 × 131 × 34 mm, weight 0.71 kgSupply 12 – 24 V DC, power consumption ≤ 8.5 WProtection IP64 (front panel)Operation -20 °C to +60 °C, storage -30 °C to +70 °CIncluded: 12 V power supply (2 A), HDMI cable, VGA cable, USB cable for touch🏷️ Manufacturer and reliabilityLilliput Electronic Technology has been developing and manufacturing monitors for industry, broadcast and vehicle applications for over 20 years. The TK series is designed for continuous operation and is CE compliant. All specifications on this page have been checked against the manufacturer's datasheet; values marked 🔍 are derived and not confirmed in writing.
- Available
- Delivery Time : 3 bis 5 Tage
Lilliput 10" touch monitor with HDMI connection 1500 Nits IP65
The Lilliput TK series are industrial touch monitors without their own CPU: image and sound come from a PC, industrial PC, Raspberry Pi or controller, and the capacitive touch is returned over USB as a standard input device. The series covers eight diagonals from 7 to 27 inches — all with high brightness, IP64 or IP65 front protection and DC supply.
🖥️ Which model fits?
Maximum brightness: the TK1019/T is the brightest and highest-resolution unit at 1500 cd/m² and 1920 × 1200. A single USB-C cable carries touch, video and power.
Rugged version: TK1331/T, TK1850/T, TK2380/T and TK2700/T feature anti-glare 7H cover glass, IK07 impact resistance, NEMA 4 at the front, automatic dimming and a touch that works with gloves and wet fingers.
Highest frame rate: only the TK2380/T has DisplayPort and therefore accepts 4K at 60 Hz — over HDMI all models take 4K at 30 Hz. It is also the only unit with a 9 to 36 V DC input range.
Wide temperature range: TK701/T, TK1019/T, TK1331/T, TK1560/T and TK2380/T operate from -20 °C. The TK2150/T is limited to 0 °C to +50 °C and therefore suits heated environments only.
Years of outdoor use: the TK2700/T is the only unit with additionally UV-resistant cover glass.
🔌 Shared features
10-point capacitive touch, driverless as a standard input device
HDMI and VGA on all models; depending on the unit also AV/RCA, DisplayPort or USB-C
DC supply 12 – 24 V DC (TK2380/T: 9 – 36 V DC), fanless
Panel mounting with supplied screw kits; VESA 75, 100 or 200 mm depending on model
Power supply, HDMI cable and USB cable for touch are included with every unit; a VGA cable with all except the TK1019/T
All models are intended for operation with a Kinco xF-SiHMI, an industrial PC or a Raspberry Pi. On the Full HD models the 1920 × 1080 resolution matches the xF-SiHMI output exactly.
🏷️ Manufacturer and reliability
Lilliput Electronic Technology has been developing and manufacturing monitors for industry, broadcast and vehicle applications for over 20 years. The TK series is designed for continuous operation and is CE compliant. All specifications have been checked against the manufacturer's datasheets; values marked 🔍 are derived and not confirmed in writing.
- Min. 1 Variant available.
- Delivery Time : 3 bis 5 Tage
New
Lilliput 15.6" AD15 Touch Monitor with HDMI/DP connection, camera, 1000 Nits IP65
If you need a machine display that not only shows and controls but also recognises who is standing in front of it, the Lilliput AD15 is a rugged 15.6-inch industrial monitor with a built-in 8 MP camera, microphone and USB hub – connected to an industrial PC or an edge box with image processing.🏭 Typical applicationsOperator station with log-in: The front camera provides the image for face recognition on the connected computer – for example to grant operating rights at the machine. The analysis is done by software on the PC, not by the monitor.Workstation with peripherals: Four USB-A ports on the monitor take scanners, RFID readers, keyboards or USB sticks. Only one USB-B cable runs to the computer.Harsh environments: IP65 and NEMA 4 at the front, 7H hardness and IK07 impact resistance, tested for vibration and shock. The touch works with wet hands and with gloves.Outdoor and windows: 1000 cd/m² with automatic dimming and a UV-resistant coating keep the image readable in sunlight.🖥️ Display15.6" LCD with 1920 × 1080 pixels (16:9)Brightness 1000 cd/m² (nits) with automatic dimmingContrast 1000:1, viewing angle 170° / 170° (horizontal / vertical)Optical bonding: no air gap between glass and panel, so less reflection and no fogging or dust behind the glassUV-resistant, anti-glare and anti-fingerprint coatingHardness ≥ 7H (ASTM D3363), impact resistance IK07 (IEC 62262)LED lifetime 50,000 h👆 10-point capacitive touchThe capacitive touch supports multi-touch gestures and, according to the manufacturer, can be operated with wet hands and with rubber, latex and PVC gloves. It is reported as a standard input device under Windows, Linux, Android and macOS – no drivers need to be installed.📷 Camera and audio8 MP front cameraMicrophone for voice recording and calls2 speakers, 3.5 mm headphone output🔌 ConnectionsThe unit is a monitor without its own CPU. The image comes from a PC, industrial PC or controller; touch, camera and USB hub connect to the computer via USB-B.HDMI 1.4b (input signal up to 4K at 30 Hz)DisplayPort (input signal up to 4K at 30 Hz)VGA (up to 1080p at 60 Hz)USB-B to the computer, 4× USB-A 3.0 as hub (1.5 A / 3 A)Power via 3-pin Phoenix terminal or DC jack, protective earth terminal💡 The AD15 has no AV (composite) input. If you want to connect an analogue camera and do not need a camera in the monitor, the same-size Lilliput TK1560/T has an AV input.With 1920 × 1080 it matches the output of the Kinco xF-SiHMI directly.🔧 Mounting and scope of deliveryRear mounting into a panel cut-out with the optional rack-mount brackets, or mounting via VESA 75 / 100 mm.Outer dimensions 383 × 245 × 40 mm, weight 2.9 kgSupply 9 – 36 V DC, power consumption ≤ 33 W (at 12 V)Protection IP65 and NEMA 4 (front panel)Vibration 1.5 Grms, 5 – 500 Hz (IEC 60068-2-64), shock 10 g, 11 ms (IEC 60068-2-27)Operation -20 °C to +60 °C, storage -30 °C to +70 °CIncluded: 3-pin Phoenix plug, HDMI cable, USB-A to USB-B cable⚠️ No power supply included. Available as options: 12 V power supply (4 A), remote control, VESA stand, rack-mount brackets🏷️ Manufacturer and reliabilityLilliput Electronic Technology has been developing and manufacturing monitors for industry, broadcast and vehicle applications for over 20 years. The AD15 belongs to Lilliput's metal-housing range and is designed for continuous operation. All specifications on this page have been checked against the manufacturer's datasheet; values marked 🔍 are derived and not confirmed in writing.
- Available
- Delivery Time : 3 bis 5 Tage
spstiger 21" Industrial Display with HDMI and Touch
High quality touch display with 21" diagonal in full HD resolution with HDMI connector for display and USB connector for touch function This display is excellent for mounting in control cabinet doors or other cutouts. It could also be mounted on a Vesa bracket.This display is ideally suited for operation on the Kinco HMI xF-SiHMI01. There are HMI from Kinco up to a size of 15". In combination of xF-SiHMI01 and this display, larger and higher resolution HMI are also possible with Kinco. .
- Available
- Delivery Time : 3 bis 5 Tage