Do you have questions? Our community may have already answered them!
Connect with others in our support forum.
Kinco CANopen bus coupler (with end cover) for Kinco RP20 modules
- CANopen slave DS301/DS401
- Up to 16 RP20 modules
- 2 × RJ45 (CAN IN/OUT)
- 125 kbit/s to 1 Mbit/s
- −20 °C to +55 °C
€108.80*
Available in 30 days, delivery time 3 bis 5 Tage
Customers also viewed
You want to connect I/O where the signals originate, and your controller speaks CANopen? The Kinco RP20C-CAN turns up to 16 modules of the RP20 series into a CANopen remote I/O station. Instead of wiring every sensor individually back to the control cabinet, you only run one bus cable and the 24 V supply to the station.
🏭 Typical Applications
Additional I/O on an existing CANopen controller: The machine already has a CANopen master, but the channels are no longer sufficient. The RP20C-CAN connects to the existing bus, the controller stays.
Decentralised stations on the machine: Conveyor lines, dosing or mixing stations get their I/O right on site. Up to 100 m between two bus nodes, approx. 40 m at 1 Mbit/s.
Building, agricultural and energy technology: Capture switching states, analogue values and temperatures from several stations over one bus line.
Mixed signals at one station: Digital, analogue and temperature in any combination, up to 16 modules per coupler.
🖥️ Key Technical Specs
Expansion: up to 16 RP20 modules via the internal K-BUS (100 Mbit/s).
Supply: 24 V DC ±20 % (19.2 – 28.8 V DC), own consumption 2 W, max. 15 W with 16 modules.
Bus current for the modules: 2.0 A at 5 V, max. 1.6 A at 55 °C.
Supply input protection: overcurrent, reverse polarity, surge.
Diagnostics: LEDs PWR, RUN, CAN and ERR; error codes in the object dictionary (0x1001, 0x1002, 0x3012) and as EMCY message to the master.
Service: USB-C for module configuration and firmware update.
🔌 CANopen Interface
Profile: CANopen slave according to DS301 and DS401.
Process data: 8 TPDOs and 8 RPDOs, communication and mapping parameters freely configurable, synchronous and asynchronous transmission.
Services: NMT, SDO, Emergency (EMCY), heartbeat and node guarding.
Connection: CAN IN and CAN OUT via 2 × RJ45 (pin 1 CAN_H, pin 2 CAN_L, pin 3 CAN_GND). Cable at least CAT5, CAT5e recommended.
Baud rate: 125 kbit/s, 250 kbit/s, 500 kbit/s or 1 Mbit/s via DIP switch.
Node ID and termination: node ID 1 to 31 and termination resistor via DIP switch.
🔗 Compatibility and Matching Modules
The RP20C-CAN works with any CANopen manager that imports EDS files. Kinco's EDS file contains the coupler and all RP20 modules. In the manual, Kinco shows commissioning with CODESYS V3.5.20.
RP20 digital modules: 8 or 16 channels, transistor or relay.
RP20 analogue modules: voltage and current, inputs and outputs.
RP20 temperature modules: Pt100, Pt1000, Cu50 or thermocouple.
RP20-PW power supply module: additional bus current for large stations.
If your controller uses EtherCAT, the RP20C-ECT is the matching coupler.
⚠️ Good to Know Before Commissioning
Configure the modules first: CODESYS does not detect the modules on the RP20C-CAN automatically. You add them with the Kinco tool KCouplerCfg or read them in by scan, and download the configuration to the coupler via USB-C. The order must match the actual mounting order, otherwise no communication is established.
Set DIP switches and master identically: Node ID and baud rate on the coupler must match the values in the master. The node ID must not be that of the CANopen manager.
Check the bus current: Each RP20 module draws 135 to 160 mA from the K-BUS. 16 digital modules already add up to about 2.2 A, more than the coupler's 2.0 A. If the total exceeds 2.0 A (1.6 A at 55 °C), add an RP20-PW power supply module to the station.
🏷️ Manufacturer and Standards
Kinco Automation develops PLCs, HMIs and drive technology. The RP20C-CAN is CE certified. EMC immunity according to IEC 61131-2, zone B: ESD 8 kV air and 4 kV contact, burst 2 kV on the supply port. Operation −20 °C to +55 °C, storage −40 °C to +70 °C, 10 to 95 % relative humidity non-condensing, up to 2,000 m altitude.
🔧 Mounting and Scope of Delivery
Mounting: 35 mm DIN rail (1 mm rail thickness) with spring latch. The modules snap on sideways via upper and lower guides. End clamps on both sides keep the station from shifting.
Supply pass-through: two internally connected 24 V terminal groups.
Dimensions: 24.3 × 100 × 80 mm (W × H × D), approx. 120 g, passive cooling, IP20.
Scope of delivery: RP20C-CAN with end cover. Kinco provides the manual, EDS file and the KCouplerCfg configuration tool for download.
Technical Specifications
Login