Do you have questions? Our community may have already answered them!
Connect with others in our support forum.
Kinco RP20 analog expansion for AK8x0M PLC and RP20 bus coupler
- 4 AI, 4 AO or 2 AI + 2 AO
- Up to 16 bit, ±0.2 % F.S.
- Current and voltage per channel
- Wire break detection
- Only 12 mm wide
€113.60*
In stock
Lieferzeit: 3 bis 5 TageCustomers also bought
Customers also viewed
You want to measure pressure, level or flow and control valves or frequency inverters with analogue signals? The analogue RP20 modules process current and voltage signals with up to 16 bits, each channel configurable individually. They plug directly onto the Kinco AK840M or onto an RP20 bus coupler.
🏭 Typical Applications
Reading transmitters: Pressure, level and flow sensors with 4 – 20 mA or 0 – 10 V.
Setting drives and valves: Setpoints for frequency inverters, proportional and control valves.
Control loops: Actual value and manipulated value in one module: the RP20-0202IV with 2 inputs and 2 outputs.
Decentralised measuring points: Together with the EtherCAT or CANopen coupler right at the plant.
🧩 Variants
RP20-0400IV: 4 analogue inputs, 16 bits: 4 – 20 mA, ±20 mA (also 0 – 20 mA), 1 – 5 V, ±10 V (also 0 – 10 V); ±0.2 % F.S., 50 conversions/s per channel, galvanically isolated.
RP20-0004IV: 4 analogue outputs, 16 bits: 4 – 20 mA, 0 – 20 mA, 1 – 5 V, ±10 V (also 0 – 10 V); ±0.2 % F.S., 50 conversions/s per channel.
RP20-0202IV: 2 analogue inputs and 2 analogue outputs, 12 bits: 4 – 20 mA, 0 – 20 mA, 1 – 5 V, 0 – 10 V; ±0.3 % F.S., 15 conversions/s per channel.
🖥️ Key Technical Specs
Inputs: input impedance 100 Ω (current) or 50 kΩ (voltage); averaging filter selectable.
Outputs: load up to 500 Ω (current), load from 1 kΩ (voltage).
Diagnostics: wire break detection in 4 – 20 mA and 1 – 5 V modes (inputs), red LED per channel when a limit is exceeded.
Supply: RP20-0004IV and RP20-0202IV additionally need 24 V DC at the terminal (approx. 100 or 80 mA).
🔗 Compatibility
The modules plug directly onto the side of the Kinco AK840M or onto an RP20 bus coupler: RP20C-ECT for EtherCAT, RP20C-CAN for CANopen. Up to 16 modules per station, configured in CODESYS (IEC 61131-3).
Digital: RP20 digital modules: 8 or 16 channels, transistor or relay.
Temperature: RP20 temperature modules: resistance thermometers and thermocouples.
⚠️ Good to Know
Set the signal type per channel: You set the measuring range and filter per channel in CODESYS; the wiring must match the selected signal type.
Galvanic isolation: Only the RP20-0400IV is galvanically isolated. RP20-0004IV and RP20-0202IV are not.
Plan the bus current: Each module draws 140 to 150 mA from the internal K-BUS. An RP20 bus coupler supplies 2.0 A (1.6 A at 55 °C), the AK8X0 1.5 A. If the total is not sufficient, add an RP20-PW power supply module to the station.
No hot swap: Only plug in or remove modules with the power switched off.
🏷️ Manufacturer and Standards
Kinco Automation develops PLCs, HMIs and drive technology. The RP20 modules are CE certified according to EN IEC 61000-6-2:2019 and EN IEC 61000-6-4:2019, EMC immunity according to IEC 61131-2, zone B. Operation −20 °C to +55 °C, storage −40 °C to +70 °C, 10 to 95 % relative humidity non-condensing, IP20.
🔧 Mounting and Scope of Delivery
Mounting: 35 mm DIN rail; the modules snap onto their neighbour sideways via upper and lower guides.
Dimensions: 12 × 100 × 80 mm (W × H × D), approx. 70 g, passive cooling.
Scope of delivery: one module of the selected variant.
Technical Specifications
Login