Kinco KC200 Frequenzumrichter

KC Driver is the software for parameterizing Kinco frequency inverters of the KC100 and KC200 series.The software supports the following functions:Connecting to the KC100 and KC200 frequency inverters via RS-485Displaying and changing the current parameters of the frequency inverterImport and export of parameter setsScoping function, for recording load curves and other characteristic curves of the frequency invertersThe frequency inverters of the KC100 and KC200 series can be parameterized via:this software via RS-485 two-wire connectionon the device itself via the control panelvia an external control panel (parameter copy function)via Modbus RTU

Everything for your Kinco KC200 after purchase – for all ten models from 1.5 to 45 kW, three-phase 400 V:Interactive wiring diagram: mains and motor, start/stop, setpoint, analog sensors, Modbus RTU, CANopen, relay and braking resistor, with cable cross-sections and parametersFirst steps: commissioning in nine steps, from the motor data to the first runOperation: keypad simulator to try out, with exercisesDimensions & mounting: dimensional drawing per model, drilling pattern, minimum clearances and a printable drilling templateDownloads: user manual, selection manual, CE documents, CANopen EDS and 2D and 3D drawingsFree support from spstiger if you get stuck

If you need a frequency inverter for pumps, fans, conveyors or hoists with more I/O, CANopen and optional speed feedback, the Kinco KC200 is a universal vector inverter from 1.5 to 45 kW for three-phase 400 V. Modbus RTU and CANopen come as standard on every model — for compact standard drives up to 5.5 kW, the smaller Kinco KC100 is available. 🏭 Typical Applications Pumps, fans and HVAC: The integrated PID controller works with two analog inputs — setpoint and actual value at the same time, without an external controller. AVR voltage regulation keeps the output voltage constant when the mains fluctuates. Hoists, agitators and heavy starts: 150 % rated current for 60 s and 180 % for 3 s, sensorless 150 % rated torque already at 0.5 Hz. With the KC200-UVWPG encoder card, this becomes closed-loop vector control with 200 % torque at 0 Hz. The brake chopper is built in up to 45 kW. Networked machines: Modbus RTU and CANopen without an add-on card. According to Kinco, up to 32 inverters can run in a master-slave group via Modbus or CAN. Brand change in existing plants: According to Kinco, the parameter addresses of the old inverter in the PLC software can be mapped to the KC200 — which makes switching brand or series easier. ⚙️ Control and Functions Three control modes: V/f control (linear, user-defined, V/f separation), sensorless vector control SVC (speed range 1:100, ±0.5 %) and, with encoder card, closed-loop vector control FVC (1:1000). Output frequency up to 599 Hz, carrier frequency up to 12 kHz, frequency resolution 0.01 Hz. Ramps: linear or S-curve, four sets of acceleration/deceleration times. Frequency setpoint via keypad, digital potentiometer, analog input, pulse input, Modbus/CANopen, PID or up to 16 preset speeds — main and auxiliary frequency can be combined. Autotuning of motor parameters, two-motor operation with alternating control of two motors. Power-loss ride-through: During a short voltage dip, the motor feeds energy back and the inverter keeps running. Fewer nuisance trips: overcurrent and overvoltage stall control, wave-by-wave current limiting on load surges, temperature-dependent carrier frequency reduction. 🔌 Connections and Control I/O 6 digital inputs (DI1–DI6): NPN/PNP, DI6 also usable as pulse input up to 100 kHz. 2 analog inputs (AI1, AI2): each 0–10 V or 0–20 mA via jumper, 12 bit. 2 analog outputs (AO1, AO2): 0–10 V or 0/4–20 mA. 2 transistor outputs (DO1, DO2): open-collector (NPN switching), 30 V / 50 mA, DO2 also as pulse output up to 100 kHz. 2 relay outputs: changeover contacts, 250 V AC / 3 A or 30 V DC / 1 A. RS-485 (Modbus RTU) and CAN (CANopen) as terminals. Port for external keypad with parameter copy between devices. ⚠️ Before Ordering No integrated EMC filter: Operation according to EN 61800-3 requires an external mains filter (Kinco filters meet category C2). Matching filters for each power rating are available separately. External brake resistor: The brake chopper is built in; the resistor is connected to ⊕/PB. Mounting clearances: at least 100 mm above and below, 50 mm at the sides. 🔧 Frame Sizes, Environment and Mounting 1.5–3.7 kW: 126 × 186 × 167 mm, approx. 2 kg 5.5–11 kW: 146 × 256 × 181 mm, approx. 6 kg 15–22 kW: 170 × 320 × 207 mm, approx. 8 kg 30–45 kW: 225 × 360 × 234 mm, approx. 9 kg IP20, wall mounting. Operation −10 °C to +40 °C, up to +50 °C with derating; storage −20 °C to +60 °C; above 1000 m, 1 % derating per 100 m. 🏷️ Manufacturer and Reliability Kinco Automation (founded 1996, listed in Shanghai) develops frequency inverters, servo and control technology for customers in more than 70 countries. The KC200 carries the CE mark (Low Voltage, EMC and RoHS Directives). Kinco frequency inverters are in productive use at numerous spstiger customers in Germany — with support in German directly from us.